Fast guide to the S-67 Smarty’s special Features

• CaTCHER software's inside

• Ten different  performance levels

• Fastest download in the industry, up to three times faster than the competition, a typical ECM update takes about 5 minutes

• ABS tire height updates in just few seconds

• Manual High Idle is enabled in all software

• Reads  Diagnostic Trouble Codes in plain text

• No tools required, no fuses to pull

• USB built in for simple updates

• Free internet updates

• Most complete keyboard in the industry

• Reliable, it works off your OEM hardware

• Programmable Speed Limiter from 25 to 250 mph

• Programmable parameters for fine tuning

• "On the fly" Power on Demand under development

• TNT software's under advanced development
   

*** Unlike the Smarty S06 for the 5.9L, the Smarty S67 is not untraceable

Attention: Smarty S67 has not been tested on 2009 trucks with ECM bootloader software produced after the date 03-04- 2009 according to the service bulletin 18-007-09. Please check the production date present on the ECM before install the CaTCHER software.

Fast guide to S-67 Smarty's software levels
The horsepower settings. except #0, all other software applications have a modified "Torque management" ( TQM). The throttle response is greatly improved but is set to a save limit. With "Save" they mean save your transmission and rest of the driveline.

• SW # 0 : Half power

• SW # 1 : 30 Hp increase, with added timing

• SW # 2 : 60 Hp increase, no added timing ***

• SW # 3 : 60 Hp increase, with added timing

• SW # 4 : 90 Hp increase, no added timing ***

• SW # 5 : 90 Hp increase, with added timing

• SW # 6 : 130 Hp increase, no added timing ***

• SW # 7 : 130 Hp increase, with added timing

• SW # 8 : 170 Hp increase, no added timing *** °°°

• SW # 9 : 170 Hp increase, with added timing °°°
   

°°° Do not use for prolonged high speed runs! Speeds exceeding approx 105 mph can result in high exhaust gas temperatures and damage the Diesel Particulate Filter (DPF) !!!
*** All even numbered software (2-4-6-8) without timing are to be used for stacking with other after market power adding devices that also add their own timing. NO additional timing has to be used with the odd numbered software (1-3-5-7-9). Severe engine damage will result !!!
 

Tested on stock trucks on the MAD Electronics in house Dyno Dynamics Twin Retarder Dyno. Stock means just that. Stock! Even the air filters were stock...

MADS Electronics checked the "baseline" ( the stock truck Hp at the rear wheels ) twice in a day in order to be sure about their findings. The above declared HP numbers are all rounded down to the closest number. For example the 90 Hp file actually did 96 Hp. That's a 90 Hp software for me, not a 100. The 170 Hp was 176.

ABS / Speedo recalibration
The tire height can be adjusted up to 44" in increments of 10 tenth of an inch in just a couple seconds. Of course, Smarty needs to be VIN# locked to the truck in order to get into the ABS adjustment section.

DTC Code reader
The name says it all.
You can read and erase codes. Codes are displayed also in plain English. That's old news by now. Smarty S-03 was the first one to provide that utility, others found the idea to be a good one too.  
( Smarty does erase ABS codes too but does not display them )

ECM update speed
Faster than anything else on the market! Again MAD Electronics has done their homework on the protocol. Less than 5 minutes. Three times faster than a Star-Scan diagnostic tool or competitor.

MADS Electronics has developed their own bootloader in order to not have to pull fuses should an update become interrupted for any reason. All you have to do is to turn the key off / key on Smarty does everything else on it's own.

Updates
The CaTCHER software as they are today are only a starting point. Expect major news in future. MADS Electronics is interested in your feedback, opinions, likes, dislikes...
MADS Electronics will make the Smarty do what YOU want, TOGETHER.