Link MINI R53 MINILINK - MINIX G4x Plug-and-Play ECU
Shipping calculated at checkout (free standard shipping to US addresses!*) (Limitations apply)
Link G4X MINILINK - MINIX
Free yourself from the constraints of the factory ECU.
NEW G4X Link of ECUs! Faster with advanced tuning features!
MiniLink - MINIXFree yourself from the constraints of the factory ECU.
The G4X MiniLink MINI-X PlugIn ECU fits the BMW Mini R53. Our BMW Mini ECU comes in it's own case which fits directly into the factory location. Installation is a breeze with no alteration of the factory wiring loom required.
A built-in connector (or pins in some models) provides additional inputs and outputs such as oil pressure inputs or anti-lag / logging switches.
MAP Sensor Not Included.
Need more inputs and outputs? The XS Expansion Loomoffers the ability to add additional inputs & outputs on our range of plug-in ECUs.
G4X PlugIn Key Features (Where Applicable)
Up to 6D fuel and ignition mapping
Precision closed loop cam control (four cam, independent control)
Sequential fuel delivery
Digital triggering, all OEM patterns
OEM idle hardware supported
5D boost control with three switchable tables
Motorsport features - antilag, launch, flat shift
Continuous barometric correction (on board)
QuickTune - automated fuel tuning
Individual cylinder correction
USB tuning cable included
Stats recording into on-board memory
Gear compensations for spark, boost and fuel
Real time selectable dual fuel, ignition and boost maps
Sync and crank sensors can be a combination of Hall effect, variable reluctance or optical
Boost control referenced to gear, speed or throttle position
Up to 32Mbit internal logging memory
Knock with "windowing"
Engine configurations are pre-set into PlugIn ECUs with a "start" base map.
Engine Temperature Dependent Soft and Hard RPM Limit
Engine Temperature Dependent Soft and Hard Boost Limit
Vehicle Speed Limit
System Voltage Limit
User Configurable RPM Limit based on external input
Up to 440 Zone Fuel Table with configurable load and RPM centres. Configurable X and Y Axis Parameters
Multiple Fuel Tables
Up to 6D Fuel Mapping
Pre Crank Prime
Post Start Enrichment
Warm Up Enrichment
IAT Fuel Correction
Injector Deadtime Compensation
Overrun Fuel Cut
Idle Load Trims
Fuel Temperature Correction
Up to 440 Zone Ignition Table with configurable load and RPM centres. Configurable X and Y Axis Parameters
Dwell Time Table. Configurable X and Y Axis Parameters
Individual Cylinder Trim
Individual Cylinder Tables
Multiple Ignition Tables
Up to 6D Ignition Mapping
Individual Cylinder Ignition Trim
Digital Trigger Decoding
Reluctor, Optical Proximity or Hall Sensors
Programmable filtering and arming thresholds
Configurable trigger patterns or preset triggering options.
Supports nearly all OEM trigger patterns and custom trigger arrangements
Antilag Group A/Group N
Auxiliary Output Options
Application specific. Output drives can be altered from OEM configuration. e.g. Purge control may be in the standard set-up. This can be re-wired and programmed in the Link Plug-in to control intercooler water spray (if added) for example.
Each Output independently configurable
Unused ignition and injection outputs available as auxiliary outputs
General Purpose Output
General Purpose PWM
Continuously Variable Valve Timing Control
Closed Loop Idle Speed Control (Solenoid or Stepper (4 & 6 Terminal))
Fuel Pump Speed Control
Air Con Clutch
Air Con Fan
Check Engine Light
Oxygen Sensor Heater
Switched Cam Solenoid
Variable Valve Timing (where applicable)
Up to 4 channel independent
Precision Closed Loop Control
3D Tables with configurable X and Y axis controls
Preset or Custom Configuration
Supported Engines - 1UZFE VVTi; Subaru AVCS; EVO 9 VVT; BMW VANOS; Toyota 3SGE, 1ZZ, IJZ, 2NZ, 2JZ; Honda K20; Nissan VQ35; Ford V8; Holden V6